BQVBL - CERAMIC REPAIR RESIN, 11700
- MSDS: BQVBL
- Manufacturer: ITW DEVCON CORP
- Product Name: CERAMIC REPAIR RESIN, 11700
- National Stock Number: 8030-00N037681
Product Identification
Product ID:CERAMIC REPAIR RESIN, 11700
MSDS Date:06/11/1990
FSC:8030
NIIN:00N037681
Kit Part:Y
MSDS Number: BQVBL
Responsible Party
DANVERS, MA 01923
US
Emergency Phone: 800-424-9300(CHEMTREC)
Info Phone: 508-777-1100
Cage: EO352
Contractor
Telephone: 215-855-8450
Cage: 20420
Ingredients
PHENOL,4,4-ISOPROPYLIDENEDI-,POLYMER WITH
CAS: 25068-38-6
RTECS: SL6475000
Fraction By Weight: 30-60%
XYLENE
CAS: 1330-20-7
RTECS: ZE2100000
Fraction By Weight: 1-5%
OSHA PEL 100 PPM;150 PPM STEL
ACGIH TLV: 100 PPM;150 PPM STEL
EPA Report Quantity: 1000 LBS
DOT Report Quantity: 1000 LBS
Hazards
LD50 LC50 Mixture:LD50:(ORAL,RAT)11.4 G/KG
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: EYES: MILD IRRITATION. FILLER
PARTICLES COULD SCRATCH CORNEA. SKIN: MINIMAL TO MILD IRRITATION IN
MOST PEOPLE. INHAL: INHALING HIGH XYLENE VAPOR CONCENTRATIONS CAN
CAUSE DIZZINESS, DROWSINESS/U NCONSCIOUSNESS. INGEST: INGRED ARE OF
LOW ACUTE ORAL TOXICITY, BUT DRAWING LIQUID XYLENE INTO LUNGS (EFTS
OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ: DURING VOMITING CAN CAUSE SEVERE LUNG
DAMAGE. CHRONIC: APPROX 1% OF WORKERS MAY BECOME SENSITIZED BY TOO
MUCH SKIN CONTACT W/EPOXY RESINS; ITCHING, SWELLING, OR RASHES MAY
THEN RESULT FROM F URTHER CONTACT. PROLONGED SKIN CONTACT W/XYLENE
CAN CAUSE DERMATITIS BY DEFATTING SKIN.
Medical Cond Aggravated by Exposure:ALLERGIES, ECZEMA, AND OTHER SKIN
DISORDERS.
First Aid
First Aid:EYES: FLUSH WITH CLEAN WATER FOR AT LEAST 15 MINUTES WHILE
GENTLY HOLDING LIDS OPEN. GET MEDICAL ATTENION. SKIN: WASH
THOROUGHLY WITH SOAP AND WARM WATER. CONSULT A PHYSICIAN IF
IRRITATION DEVELOPS. I NHAL: REMOVE TO FRESH AIR. ADMINISTER OXYGEN
IF BREATHING IS DIFFICULT. GET MEDICAL ATTENTION. INGEST: GET
MEDICAL HELP; GIVE WATER TO DILUTE, UNLESS PATIENT IS UNCONSCIOUS.
DO NOT INDUCE VOMITING.
Fire Fighting
Flash Point Method:TCC
Flash Point:>200F,>93C
Lower Limits:1%
Upper Limits:7%(XYLENE)
Extinguishing Media:CARBON DIOXIDE, DRY CHEMICAL, FOAM.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:NONE.
Accidental Release
Spill Release Procedures:PREVENT SKIN CONTACT. SCRAP UP AND DISCARD IN
SUITABLE CONTAINERS, USING INERT ABSORBENT MATERIAL SUCH AS
VERMICULITE IF NEEDED. WASH SPILL AREA WITH AN INDUSTRIAL CLEANING
AGENT; IF SOLVENT IS USED, TAKE CARE AGAINST EXPOSURE AND FIRE.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:STORE WELL CLSD IN A COOL, DRY PLACE.
AFTER MIXING W/HARDENER, OBSERVE PREC RECOM FOR HARDENER. AFTER
PROPER CURING, PROD IS NOT HAZ.
Other Precautions:WHEN SANDING/MACHINING CURED MATERIAL, TAKE PROPER
PRECAUTIONS AGAINST INHALATION OF DUSTS GENERATED.
Exposure Controls
Respiratory Protection:NONE REQUIRED @ NORMAL HANDLING TEMPERATURES.
USE NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE FOR EXPOSURE OF
CONCERN .
Ventilation:PROVIDE ADEQ VENT TO KEEP VAPS BELOW TLV. LOC EXHAUST IS
RECOM FOR CONFINED AREAS; GEN MECH VENT IS ADEQ FOR NORM USE.
Protective Gloves:CHEMICAL RESISTANT GLOVES.
Eye Protection:SAFETY GLASSES WITH SIDE SHIELDS.
Other Protective Equipment:OTHER PROTECTIVE GEAR.
Work Hygienic Practices:WASH THORO AFTER USING, ESP BEFORE EAT/SMOKING.
CONTAMD CLTHG & PROT GEAR SHOULD BE REMOVED & CLEANED BEFORE (SUPP
DATA)
Supplemental Safety and Health
HYGIENE PRACT: RE-USE. LEATHER ARTICLES SUCH AS SHOES & BELTS CANNOT BE
DECONTAMINATED AND SHOULD BE DISCARDED.
Chemical Properties
Vapor Pres:<4@78F
Vapor Density:>1
Spec Gravity:1.66
pH:NEUT
Evaporation Rate & Reference:<1(BUTYL ACETATE=1)
Solubility in Water:APPROX 1/2%
Appearance and Odor:DARK BLUE PASTE WITH LITTLE ODOR.
Stability
Stability Indicator/Materials to Avoid:YES
STRONG ACIDS, BASES AND OXIDIZERS.
Stability Condition to Avoid:OPEN FLAME AND EXTREME HEAT.
Hazardous Decomposition Products:OXIDES OF CARBON; ALDEHYDES AND ACIDS
FROM INCOMPLETE COMBUSTION.
Conditions to Avoid Polymerization:HEAT IS RELEASED WHEN RESIN IS MIXED
W/EPOXY HARDENER. USE CAUTION WHEN MIXING A POUND/MORE.
Disposal
Waste Disposal Methods:XYLENE IS A RCRA-LISTED HAZARDOUS WASTE(U239);
DISPOSE OF IN ACCORDANCE WITH FEDERAL, STATE, AND LOCAL
REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.